TRAINING ONLINE PUMPS & COMPRESSORS FOR NON ENGINEER

TRAINING ONLINE PUMPS & COMPRESSORS FOR NON ENGINEER

training

DESKRISPSI TRAINING WEBINAR POMPA & KOMPRESOR UNTUK NON ENGINEER

Pompa banyak digunakan di pabrik proses petrokimia, sistem sirkulasi air, A/C dan sistem pemanas, dan banyak aplikasi lainnya. Kompresor banyak digunakan dalam berbagai aplikasi.

Menjaga mesin ini berjalan dengan sedikit masalah dan mematikan mengurangi waktu henti seluruh sistem. Pemilihan alat berat yang tepat sesuai dengan aplikasi yang tepat, pengoperasian alat berat yang tepat, program perawatan yang efektif, sistem pemantauan yang andal, dan personel terampil yang mampu melakukan pemecahan masalah yang tepat merupakan persyaratan penting untuk memperpanjang masa pakai alat berat. Semua hal di atas dapat dicapai melalui pemahaman yang lebih mendalam tentang konstruksi dan toleransi mesin, batasan dan kendala dalam pengoperasiannya, serta metode pengendalian yang lebih efektif.

Menimbang cukup kompleknya materi pelatihan PUMPS & COMPRESSORS for Non Engineer ini bagi peserta, dibutuhkan training provider yang berpengalaman di bidangnya agar tidak membuat peserta tidak menjadi cepat bosan dan jenuh dalam mendalami bidang teknik ini.

TUJUAN TRAINING PROBLEMS AND SOLUTIONS FOR PUMPS AND COMPRESSORS UNTUK PRAKERJA

Dengan mengikuti pelatihan PUMPS & COMPRESSORS for Non Engineer Peserta dapat berbagi pengetahuan / sharing knowledge mengenai PUMPS & COMPRESSORS for Non Engineer dengan peserta dari perusahaan lain yang bergerak di bidang PUMPS & COMPRESSORS for Non Engineer

MATERI pelatihan POMPA & KOMPRESOR untuk Non Engineer online Zoom pelatihan problems and solutions for pumps and compressors online Zoom

* Pumps and compressors: Types of Performance

1. Pumping methods: Centrifugal, Lifting, and Forcing

2. Pumps and compressors classifications and range of operation\

* Positive displacement,

* Rotodynamic pumps and compressors :

1. Rotary Pumps and compressors

* Internal gear, external gear, loop, sliding-vane:

1. Comparison between different types of rotary pumps and compressors

2. Dynamic pumps and compressors: Centrifugals and axial-flow pumps and compressors

* Comparison between centrifugals and rotary pumps and compressors

* Pump performance curves, measurements and calculations

* Characteristics of the pump curves

* Different types of losses, prewirl, hydraulic losses, mechanical and volumetric losses

* Factors affecting pump performance curves

* Similarity laws, specific speed and specific diameter

* Effect of speed variation, effect of impeller diameter trimming

* Pumps and compressors: Operation and Control :

1. Major items in pump operation

2. Basic concepts of pump operation

3. Piping system

* Pump curves versus system curves

* Operating point and system H-Q curve calculation

* Pressure drop due to piping

* Pressure drop due to piping fittings and equipments

* Pump load

* Sizing suction and discharge piping

* NPSH available

1. Method of calculation

2. Suction system configuration

3. Cavitation

4. NPSH required, measurement, calculation, standards

* Operating conditions

1. Normal operating range, minimum and maximum flow rate limits

2. API standard recommendations

3. Off-design operation and power losses

4. Pump surging and Surge prevention

5. Parameters affecting the pump operation

* Capacity Regulation

1. Methods of capacity control

2. Bypass and Recirculation systems

3. Control methods and power saving

* Series and parallel operation

1. Why series and parallel connection?

2. As a method of capacity control

3. Multistage pumps and compressors

* Trouble free operation

1. Operation under cavitation conditions

2. Ways of reducing cavitation

3. Super cavitation pumps

4. Operation at reduced flow rate

* Pump starting and shutdown

1. Motor load at starting and at shutdown

2. Priming, self-priming

* Operation difficulties

1. Operation problems and solutions

2. Selection and Specifications

* Pump and Compressor standards

1. Standards in USA

2. HI standards

3. Universal standards

4. API standards and specifications

* Pump and compressor selection

1. pumps and compressors Selection procedure

2. Manufacturer data and curves

3. Liquid properties, slurry and Ph number

4. Material selection

5. Hot and cold applications

* Pump performance curve correction

* Pumps and compressors applications, selection and inquiries

1. Pumping arrangement ,prime movers

2. Economical consideration and special applications

3. Advantages and disadvantages of centrifugal pumps and compressors

4. Features of other types of pumps and compressors

* Packing and Mechanical Seals

* Packing

1. Shaft sealing

2. Packing sizing and materials

3. Packing installation

* Mechanical seals

1. Basic concepts of mechanical seals

2. Comparison with thrust bearings

3. Types of mechanical seals

4. Balanced and un-balanced type

* Seals configurations

1. Single and Multiple seals

2. Tandem type

3. Double and Dual seals

* Mechanical seal components

1. Primary and Secondary components

2. Elastomers

* Comparison between packing and mechanical seal

* Hydraulic loads on Bearings: Radial and Axial loads

* Axial load balancing; Balance disk and double suction pumps and compressors

* Anti-friction bearings:

1. Bearing loads and Maximum-capacity bearings

2. Bearing misalignment capacity

3. Ball bearing fits, housing fits and shaft fits

* Hydrodynamic bearings

1. Self- and non-self-aligning bearings

2. Lubrication methods

* Troubleshooting and Maintenance

* Principles of troubleshooting

* Maintenance: concepts and Strategies

* Balancing and Vibration: Vibration sensors and analysis

* Classes of troubles

* Methods of diagnosis

* Monitoring and Data collection

* Main problems of the centrifugal pumps and compressors

1. Causes of pump failure

2. Improper repair/installation

3. Improper operation

4. Causes due to fluid , gas pockets, Suction and System troubles

5. Mechanical troubles and seals failure

6. Bearing failure ;Bearing life and Bearing lubrication

* Shaft deflections

1. Misalignment

2. Problems caused by shaft deflection

* Cavitation in Pumps

1. Types of cavitation

2. Failure due to cavitation

3. Cavitation diagnosis

4. Reducing and eliminating causes of cavitation

* Minimum flow rate problems

1. Failure due to reduced flow rate

2. Bypass systems a solution to reduced flow problems

Studi Kasus / Praktek pemecahan masalah PUMPS & COMPRESSORS for Non Engineer

METODE &&&

Metode Training PUMPS & COMPRESSORS for Non Engineer dapat menggunakan fasilitas training zoom atau training online, dan bisa juga training offline atau training tatap muka.

INSTRUKTUR pelatihan seals and bearings on pumps and compressors availability online Zoom

Instruktur yang mengajar pelatihan PUMPS & COMPRESSORS for Non Engineer ini adalah instruktur yang berkompeten di bidang PUMPS & COMPRESSORS for Non Engineer baik dari kalangan akademisi maupun praktisi.

PESERTA

Peserta yang dapat mengikuti training PUMPS & COMPRESSORS for Non Engineer ini adalah staff sdm atau karyawan yang ingin mendalami bidang PUMPS & COMPRESSORS for Non Engineer .

Karena kompleksnya pelatihan ini, maka dibutuhkan pendalaman yang lebih komprehensif melalui sebuah training. Dan menjadi sebuah kebutuhan akan training provider yang berpengalaman di bidangnya agar tidak membuat peserta menjadi cepat bosan dan jenuh dalam mendalami bidang teknik ini.

LOKASI PELATIHAN
  1. YOGYAKARTA  – Hotel Dafam Malioboro
  2. JAKARTA – Hotel Amaris Tendean
  3. BANDUNG – Hotel Verona Palace Bandung
  4. BALI –  Hotel Eden Kuta
  5. LOMBOK  NTB– Lombok Plaza Hotel
  6. ONLINE TRAINING via ZOOM
  7. IN HOUSE TRAINING

*Waktu dan Tempat pelaksanaan pelatihan bisa kami sesuaikan dengan kebutuhan peserta.

Jadwal Pelatihan Jakarta Training 2023 :

Batch 1 : 03 – 04 Januari 2024 | 16 – 17 Januari 2024 || Batch 2 : 06 – 07 Februari 2024 | 20 – 21 Februari 2024

Batch 3 : 05 – 06 Maret 2024 | 19 – 20 Maret 2024 || Batch 4 : 03 – 04 April 2024 | 23 – 24 April 2024

Batch 3 : 26 – 28 Juni 2023

Batch 7 : 09 – 10 Juli 2024 | 23 – 24 Juli 2024 || Batch 8 : 06 – 07 Agustus 2024 | 20 – 21 Agustus 2024

Batch 9 : 04 – 05 September 2024 | 18 – 19 September 2024 || Batch 10 : 08 – 09 Oktober 2024 | 22 – 23 Oktober 2024

Batch 11 : 06 – 07 November 2024 | 26 – 27 November 2024 || Batch 12 : 04 – 05 Desember 2024 | 18 – 19 Desember 2024

CatatanJadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta.

Investasi Pelatihan Jakarta Training

  1. Investasi pelatihan selama tiga hari tersebut menyesuaikan dengan jumlah peserta (on call). *Please feel free to contact us.
  2. Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.
Fasilitas Pelatihan di Jakarta Training

1. Hotel

2. Module / Handout

3. FREE Flashdisk

4. Sertifikat

5. FREE Bag or bagpackers (Tas Training)

6. Training Kit (Dokumentasi photo, Blocknote, ATK, etc)

7. 2xCoffe Break & 1 Lunch, Dinner

8. FREE Souvenir Exclusive

9. Training room full AC and Multimedia

Leave a Reply

Your email address will not be published. Required fields are marked *